You have downloaded bizkontrol 3 or more times, to download it again please contact us at email@example.com
To Activate your account, please
Verify your Email address
by clicking the Link confirmation Email sent by us.
Verification link is valid for 15 days only.
You're almost done,just verify your mobile by entering the verification code sent
on your mobile.
Your Mobile Number :
Provide Information Like:
- Exact product name / size / specification
Enter estimated order Quantity & select the Unit from the list e.g. 1000 Nos, 10 Tons
SKEY PRODUTS manufactures LUBOMATIC range of centralised Lubrication System For Sugar Mill bearings . The System consists of following components :-
A very highly reliable pump with high discharge pressure is incorporated in the system. The pump is reciprocating plunger type pump, which is kept immersed in Oil . This pump is driven by a geared motor . Considering the continuous Opration of system all the components are manufactured to very close tolerance & a special grade material is used to ensure consistent performance . The working principal of the pump is very simple and performs non-stop with very high delivery pressure. A standby pump is also provided.
A continuous duty electric geared motor with service factor of 2.9 is used. The motor used is a TEFC squirrel cage induction motor suitable for 415 VAC, 3Phase, 50Hz, AC supply as per IS 325 with class B insulation .It is a geared motor with 125 RPM & 0.55 kw rating .
The pump driven by geared motor is kept immersed in oil to ensure long life & efficient working . The reservoir is of 50 lit . Capacity which is mounted on a pump housing . A level switch fitted to indicate low oil level in tank. Two oil level gauges are located on the front side of reservoir to check the oil level visually.
CHANGE OVER VALVES
The valve is hydraulically/electrically operated when the pump is switched ON the line 1 is connected and the pressure goes on increasing and when it reaches set high pressure all the points are lubricated as the valve moves forward the line gets blocked and the pressure goes on increasing and line changes to no. 2 line this goes on repeating. The dwell time is adjusted as per requirement and after set dwell time the cycle goes on repeating.
Two electric control panels which consists of Main Power Supply, Contactor, MCB etc., It ensure the smooth working of the system. In case of any faults the alarm is provided with visual indications. The selection of system 1 & System 2 ( Stand by Pump ) can be done using selector switch provided.
When the line pressure drops down the set pressure. The pressure switch gives signal to control panel & alarm is indicated on the panel & hooter switched ON
A relief valve is provide to safeguard the pump from overloading. By adjusting the relief valve setting the delivery pressure can be increased and decreased.
PIPING & FITTINGS
High quality seamless pipes are used to work under high pressures
Fittings of high quality standards are used to ensure leakage free consistent Working of the system. Various hydraulic fittings are used, such as male stud Elbow, Unequal Tee, Pipe Connector, Straight Connectors. Flexible Polyhoses are used wherever required.
WORKING OF THE SYSTEM
LUBOMATIC Centralised dual line lubrication system basically consists of a reservoir with built in reciprocating plunger pump immersed in the oil, change over valve, dose feeders ( Dual line metering elements ) Pressure Switch, pipes, hose pipes, fittings Electrical Control Panel etc.
In this type of system, there are two main lines of 16 OD, which run parallel to the Sugar Crushing Mill Tandem. From these two main lines, 10 OD Pipes are connected to inlet of dose feeders & the outlet of the dose feeders are connected to the lubrication points ( bearings ).
The valve is hydraulically / electrically operated when the pump is switched ON the line 1 is connected and the pressure goes on increasing and when it reaches set high pressure all the points are lubricated as the valve moves forward the line gets blocked and the pressure goes on increasing and line changes to no. 2 line this goes on repeating. The dwell time is adjusted as per requirement and after set dwell time the cycle goes on repeating.
The discharge of oil can be controlled by